【英文标准名称】:StandardSpecificationforFabricatedorCastAutomaticSelf-Cleaning,FuelOilandLubricatingOilStrainers
【原文标准名称】:制造的或铸造的自动清洗燃料油和润滑油过滤器标准规范
【标准号】:ASTMF1567-1994
【标准状态】:现行
【国别】:美国
【发布日期】:1994
【实施或试行日期】:
【发布单位】:美国材料与试验协会(ASTM)
【起草单位】:ASTM
【标准类型】:()
【标准水平】:()
【中文主题词】:润滑油过滤器;清洁处理;自动;滤器;燃料;一般;造船材料;自动清洗过滤器;清洗过滤器;连续自身;建造的;燃料油过滤器;自身;单一过滤器;铸造;润滑油;燃料油
【英文主题词】:Cast;Cleaning;Fuels;Lubricatingoils;Lubrication;Oils;Shipbuilding;Strainers
【摘要】:
【中国标准分类号】:J21
【国际标准分类号】:21_260
【页数】:7P;A4
【正文语种】:英语
Product Code:SAE J1939/73
Title:Application Layer - Diagnostics
Issuing Committee:Truck Bus Control And Communications Network Committee
Scope:The SAE J1939 series of recommended practices are intended for light- and heavy-duty vehicle uses on- or off-road as well as appropriate stationary applications which use vehicle-derived components (e.g. generator sets). Vehicles of interest include, but are not limited to: on- and off-highway trucks and their trailers, construction equipment, and agriculture equipment and implements.The purpose of these documents is to provide an open interconnect system for on-board electronic systems. It is the intention of these documents to allow electronic devices to communicate with each other by providing a standard architecture.J1939-73 identifies the diagnostic connector to be used for the vehicle service tool interface and defines messages to accomplish diagnostic services. California-regulated OBD II requirements are satisfied with a subset of the specified connector and the defined messages. Diagnostic messages (DMs) provide the utility needed when the vehicle is being repaired. Diagnostic messages are also used during vehicle operation by the networked electronic control modules to allow them to report diagnostic information and self-compensate as appropriate, based on information received. Diagnostic messages include services such as periodically broadcasting active diagnostic trouble codes, identifying operator diagnostic lamp status, reading or clearing diagnostic trouble codes, reading or writing control module memory, providing a security function, stopping/starting message broadcasts, reporting diagnostic readiness, monitoring engine parametric data, etc.
基本信息
| 标准名称： | 袖珍式橡胶国际硬度计检定规程 |
| 英文名称： | for Pocket Hardness Meter of International Rubber Hardness Degree |
| 中标分类： |
综合 >>
计量 >>
力学计量 |
| 发布部门： | 国家技术监督局 |
| 发布日期： | 1989-04-06 |
| 实施日期： | 1990-02-01 |
| 首发日期： | |
| 作废日期： | |
| 归口单位： | 广东省标准计量管理局 |
| 起草单位： | 广东省计量科学研究所、山东省计量科学研究所 |
| 起草人： | 林鲁山 |
| 出版社： | 中国计量出版社 |
| 出版日期： | 1990-02-01 |
| 页数： | 11页 |
| 书号： | 155026-1353 |
适用范围
本规程适用于新制造、使用中及修理后的袖珍式橡胶国际硬度计的检定。
前言
没有内容
目录
没有内容
引用标准
没有内容
所属分类： 综合 计量 力学计量